Option

Curve generator option


Type	GV1-20HT	GV1-20HAW-PF	GV1-20HAW-PF-4MT	GV2-60H(P)T	GV2-60PAW-5MT	GV2-60PAT-R	KCG2-80H(P)	GNH2-80PAS	GNV2-150	GNV3-250	GNV4-400	GNV5-800	KCG6-80H	KCG6-80W	KCG7P-200
Diaphragm chuck	●	●	●	●	●
Collet chuck							●	●					●	●	●
Air chuck									●	●	●	●
Lens adaptor	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Coolant tank(with pump)	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Micro separator	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Adapter jig	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Oil pan	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Caster	●	●	●	●	●	●	●	●					●	●	●
Grinding wheel length measuring instrument							●	●	●	●	●	●
Wheel spindle inverter	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Centering measurement instrument(with dial gauge)	●	●	●	●	●	●			△	△	△	△
Beveling unit	●	●	●	●	●	●	△	△					●	●	●
Beveling unit Attachment base	●	●	●	●	●	●
Leveling device(anti-vibration type)	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Ring spherometer	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Digital display(circular axis, cross axis)	●	●	●	●	●	●							●	●	●
Test bar	●	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Signal tower	●	●	●	●	●	●	●	●	●	●	●	●
Chuck open/close foot switch							●	●	●	●	●	●
Duct port									●	●	●	●
Mist collector									●	●	●	●
Fine infeed unit													●	●	●
Automatic oil supply device													●	●	●
Manual oil supply device													●	●	●
Recessed jig chuck						●	●	●	●	●	●	●	●	●	●
Process data memory							●	●	●	●	●	●
Current control									●	●	●	●


Type	S(P)U01-15M	S(P)U022-15M	S(P)U12-25M	KS(P)6-60	KS(P)7-150	KOH-01-S(P)1	KOH-42-S(P)2	KOH-44-S(P)2	KOH-28-S(P)2	KOH-210-S(P)2	KS(P)U-200	KS(P)U-300	S(P)051-800	S(P)NC22-80M
Lens holder	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Coolant tank(with pump)	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Micro separator	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Centering adapter	●	●	●	●	●									●
Deflection measuring table(with a dial gauge)	●	●	●	●	●									●
Automatic sizing instrument *Supports a smoothing machine only	●	●	●	●	●									●
Workpiece suction device	●	●	●								●	●
Ring spherometer	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Tool plate	●	●	●	●	●	●	●	●	●	●	●	●	●	●
Set gauge	●	●	●	●	●
Swing arm for small workpiece				●	●
Frequency converter(2-step selectable)				●	●									●
Oil pan				●	●						●	●		●
Leveling device(anti-vibration type)				●	●	●	●	●	●	●	●	●	●	●
Caster				●	●
Main spindle adapter						●	●	●	●	●			●
Setup spacer						●	●	●	●	●			●
Zero set adjustment block						●	●	●	●	●			●
Pressure variation device						●	●	●	●	●	●	●	●
Digital display(upper spindle longitudinal position, lower spindle angle)											●	●
Variable tool spindle rotation speed											●	●


Type	CNV2-60AT	CNV2-80A	CNV3-300	CNV4-500
Bell holder(up and down)	●	●	●	●
Coolant tank(with pump)	●	●	●	●
Micro separator	●	●	●	●
Mist collector	●	●	●	●
Holder cutting tool table(for use on the machine)	●	●	●	●
Holder cutting machine(for outside the machine)	●	●
Oil pan	●	●	●	●
Measurement gauge(centering measurement instrument, dial gauge)	●	●	●	●


Type	MNV2-80	MNV3-300	GNV4-200T
Diaphragm chuck	●	△	△
Air chuck	△	●	●
Lens adaptor	●	●	●
Coolant tank(with pump)	●	●	●
Micro separator	●	●	●
Adapter jig	●	●	●
Oil pan	●	●	●
Grinding wheel length measuring instrument	●	●	●
Wheel spindle inverter	●	●	●
Centering measurement instrument(with dial gauge)	●	△	△
Leveling device(anti-vibration type)	●	●	●
Ring spherometer	●	●	●
Test bar	●	●	●
Signal tower	●	●	●
Chuck open/close foot switch	●	●	●
Duct port	●	●	●
Mist collector	●	●	●
Recessed jig chuck	●	●	●
Process data memory	●	●	●
Current control	●	●	●